Frequently Asked Questions are used to provide additional information and/or statutory guidance not found in State Medicaid Director Letters, State Health Official Letters, or CMCS Informational Bulletins. The different sets of FAQs as originally released can be accessed below.
Frequently Asked Questions
Do I need to use value sets to calculate these institutional rebalancing and utilization measures? If so, where can I find the value sets?
Yes. Value sets are the complete set of procedure and codes used to identify a service or condition included in a measure. All three of the rebalancing measures—LTSS Admission to an Institution from the Community, LTSS Minimizing Institutional Length of Stay, and LTSS Successful Transition after Long-Term Institutional Stay—use the "Institutional Facility"value set (XLSX, 2.88 MB). See Table 2 in the "LTSS Value Sets to Codes" tab. Table 1 in the "LTSS Measures to Value Sets" tab shows each value set needed for each measure.
FAQ ID:91106
SHARE URLShould unpaid or denied claims be included in calculating the institutional utilization and rebalancing measures?
No, include paid claims only (days denied for any reason should not be included) for all three of the rebalancing measures—LTSS Admission to an Institution from the Community, LTSS Minimizing Institutional Length of Stay, and LTSS Successful Transition after Long-Term Institutional Stay.
FAQ ID:91111
SHARE URLWhen a facility has been in operation for the dates of service covered by the Upper Payment Limit (UPL) demonstration, can a state demonstrate the UPL by using less than 12 months of data?
In accordance with Medicare cost reporting, the state must use 12 months of cost data reported by each facility. With regard to payment data, the state should use actual amounts, to the extent available, then calculate a claims completion factor based on historic utilization. The state’s UPL submission must include an explanation of its methodology to estimate payments. The use of a claims completion factor provides a reasonable estimate of the amount that Medicare would pay for these services, consistent with the UPL as defined at 42 CFR 447.272.
FAQ ID:92446
SHARE URLWhat data should my state provide to the Centers for Medicare & Medicaid Services (CMS) for the annual Upper Payment Limit demonstrations?
Effective state fiscal year 2020, each state must submit a complete data set of payments to Medicaid providers, including providers paid at cost, as well as critical access hospitals. This would require states to submit cost and payment data to CMS that previously was not requested.
FAQ ID:92456
SHARE URLHow will the Centers for Medicare & Medicaid Services (CMS) disseminate the list of Healthcare Common Procedure Coding System (HCPCS) codes subject to the federal financial participation (FFP) limit each year?
Annually, CMS will request a list of covered durable medical equipment HCPCS codes from the Medicare Pricing, Data Analysis and Coding Contractor. Once the list is received, CMS will distribute the list through the CMS Regional Office Associate Regional Administrator.
FAQ ID:93671
SHARE URLStates have raised concerns around the federal financial participation (FFP) limit demonstration due date because they may not have received all durable medical equipment (DME) claims from providers at the point demonstrations are due. How may a state ensure compliance with the FFP limit without allowing for a claims run-out period.
To address claims run-out and ensure compliance with the FFP limit, we recommend states with these concerns conduct interim FFP limit demonstrations for DME no later than three months after the end of the calendar year for the previous calendar year (that is, January 1-December 31). The interim DME FFP limit demonstration will be due by March 31 of each calendar year and will contain data for the period of January 1 to December 31 of the preceding year. The final demonstration would be due one year later on March 31 and include all claims received during the run-out period dates of service within the interim demonstration period. The interim demonstration process should provide states with an understanding of potential violations of the FFP to make any necessary budgeting and rate changes. This method is being used to allow provide for a reasonable claims run out period as allowed under 42 CFR 424.44, which states that claims must be filed no later than one calendar year after the date of service.
FAQ ID:93676
SHARE URLCan you explain the difference between a prospective Upper Payment Limit (UPL) and a retrospective UPL?
The difference between a prospective and retrospective UPL is in the relationship between the UPL demonstration period and the date when the UPL is submitted. For a UPL demonstration period of 7/1/2018 to 6/30/2019, a UPL is considered retrospective when it is submitted on or after the start of the demonstration period (on or after 7/1/2018). Using the same UPL demonstration period (7/1/2018 to 6/30/2019), a UPL is considered prospective if it is submitted prior to 7/1/2018.
FAQ ID:92431
SHARE URLWhen is the federal financial participation (FFP) limit demonstration due? And for what period of time? Why is the Centers for Medicare & Medicaid Services using calendar year for this demonstration?
Federal financial participation (FFP) limit demonstrations for durable medical equipment (DME) will be due 3 months after the end of the calendar year for the previous calendar year (i.e., January 1-December 31). The first DME FFP limit demonstration will be due by March 31, 2019 and will contain data for the period of January 1, 2018 to December 31, 2018. This reporting period was selected to coincide with the effective date of the statute (January 1, 2018).
FAQ ID:93486
SHARE URLCan you clarify that for each Healthcare Common Procedure Coding System code, a state should use the state-specific rate, which is adjusted by Medicare based on state specific geographic adjustors, and not the floor rate, which is Medicare's national rate for each specific code?
The statute does not compel states to set their payment rates for durable medical equipment (DME) at specific Medicare rates for each specific item. Instead, the statute applies a limit on available federal financial participation (FFP) for state aggregate expenditures. States have the flexibility to set their own rates for DME in the Medicaid program. If a state decides to set their Medicaid payment rates at or below Medicare rates in the state plan, the state should be specific about the fee schedule the state will use and be prepared to demonstrate that their rates do not exceed the amount Medicare would have paid in the aggregate, in order to avoid the annual FFP limit demonstration of aggregate expenditures. For the demonstration, the Centers for Medicare & Medicaid Services (CMS) will be using state-specific Medicare payment rates. With this limit of available FFP for the aggregate amount of DME, CMS will use either the Medicare rates specific to an area of the state for the services rendered in those areas, or the lowest of a state’s Medicare rates for comparison to the aggregate limit of FFP.
FAQ ID:93491
SHARE URLAre state's allowed to use state-only funds to pay the difference on a durable medical equipment (DME) item where a state may need to pay more for a particular item that would otherwise be allowed under the Medicare program?
States are free to establish higher rates for particular items of DME if they determine that higher rates are needed under the Medicaid state plans. If, however, the aggregate expenditures would exceed the Medicare rates in the aggregate, federal financial participation (FFP) would be limited. States that determine that payments above Medicare aggregate totals are necessary may use state-funds to obtain particular items of DME. The statute specifically describes an aggregate limit on state expenditures only for purposes of paying FFP. Therefore, a state may pay more than the Medicare rate for a particular item of DME, and as long as the aggregate amount for all DME is not exceeded, no FFP is at risk. Even if the aggregate amount is exceeded, there is only a limit on FFP, and there is no limit on the use of state funds used on DME items.
FAQ ID:93496
SHARE URL